Search found 18 matches

by grumpus
Fri May 03, 2019 7:33 pm
Forum: Wanted
Topic: MPH Speedo
Replies: 3
Views: 930

Re: MPH Speedo

Please define STRONG MONEY !!!!
by grumpus
Fri May 03, 2019 7:30 pm
Forum: Wanted
Topic: FEW PARTS NEEDED
Replies: 0
Views: 1080

FEW PARTS NEEDED

As above I need a few small parts, so if any one has any of the following they would part with?
L/H side fairing bracket, Upper, and lower.
L/H inner fairing air scoop.
Kickstart stopper bracket.

Thanks for looking.
by grumpus
Fri May 03, 2019 7:26 pm
Forum: Bodywork
Topic: chain guard decal location
Replies: 5
Views: 1156

Re: chain guard decal location

Thanks.
Whats the other decal shown in the image? tire pressures or something?
by grumpus
Tue Apr 23, 2019 7:13 pm
Forum: Bodywork
Topic: chain guard decal location
Replies: 5
Views: 1156

chain guard decal location

Hi all. my build is nearing completion, and to add the finishing touches I've bought the missing warning decals off the bay. the chain guard warning decal (as shown on the parts list on CMS ) shows the decal on the top edge of the guard ( uppermost face) is this the correct location? any images woul...
by grumpus
Wed Apr 17, 2019 6:57 pm
Forum: Engine, Clutch & Gearbox
Topic: ATAC setup
Replies: 1
Views: 615

ATAC setup

Hi all.
any tips on setting up the ATAC valves?
The manual states certain clearances but to check you must run the engine at 7000 rpm, so the valve is actuated?
can it be done whilst the engine is static?
Any help, tips much appreciated !
many thanks
by grumpus
Sun Jan 27, 2019 5:38 pm
Forum: Electrical
Topic: Neutral switch wire
Replies: 2
Views: 843

Neutral switch wire

Hi all. anyone got a diagram of the the connectors that go on the back of the ignition coils, 2 two that mount on the right hand side of the frame. also I cant find where the the neutral switch wire connects into the loom,It looks original, has a male round bullet connector on the end but it is rout...
by grumpus
Thu Jan 17, 2019 10:42 pm
Forum: Other
Topic: Another new member (plus help needed)
Replies: 19
Views: 2928

Re: Another new member (plus help needed)

Welcome ! I am a relatively new member on here having bought my first NS. Currently undergoing frame up restoration. I also own a GPZ900r with 16 inch front wheel, never really had an issue once you get used to it, and some good rubber out there. I mainly use BT45 Bridgestone battleaxe. ps. also own...
by grumpus
Sat Jan 12, 2019 6:11 pm
Forum: Other
Topic: Coolant temp sender
Replies: 2
Views: 882

Coolant temp sender

Hi
I need a new temp sender unit thingy, found them on CMSNL but 70 euro's is taking the pee.
sw-assythermo_big37760ZG5003-01_9598.jpg


anyone know of an alternative that will fit ? or have a second hand one laying around
product number: 37760KM9000
supersession: 37760ZG5003
by grumpus
Tue Jan 08, 2019 7:24 pm
Forum: Carburetion
Topic: Petrol Cap rebuild kit
Replies: 6
Views: 1557

Re: Petrol Cap rebuild kit

Hi Alistair.
I think you are able to supply me with new carb rubbers, (I did send you a PM but it seems to be stuck in the outbox)
Anyway I need the replacement rubbers, so How do I proceed? I believe you operate an exchange service for £135?
could you let me know how to proceed?
many thanks.
Graham
by grumpus
Thu Jan 03, 2019 8:48 pm
Forum: Other
Topic: VIN Plate
Replies: 4
Views: 1009

VIN Plate

Hi, Im missing the vin plate from my frame (I think) on the right side of the frame at he front, on the top of the square section there are two holes but no plate? I assume this would be where it should be? The frame stamping on the headstock is all there, and doesn't look like its been messed with ...
by grumpus
Thu Jan 03, 2019 8:37 pm
Forum: Engine, Clutch & Gearbox
Topic: Engine mounts
Replies: 11
Views: 1665

Re: Engine mounts

I didnt contact FLP as I didnt purchase the bike, it was a friend of mine. He bought the bike whilst recovering from a nasty accident ( He was rear ended on his Triumph Thruxton ) As such the bike wasnt used for 6 months, it was bought at Stafford in the October, and was first used the following spr...
by grumpus
Mon Dec 31, 2018 1:48 pm
Forum: Carburetion
Topic: Petrol Cap rebuild kit
Replies: 6
Views: 1557

Petrol Cap rebuild kit

Hi all,
I remember seeing on facebook somewhere (in Japan) I think that were selling a new seal kit for the petrol filler cap, but I cant remember where/or the company.
any pointers???
by grumpus
Mon Dec 31, 2018 11:47 am
Forum: Engine, Clutch & Gearbox
Topic: Engine mounts
Replies: 11
Views: 1665

Re: Engine mounts

sorry to hear your issues, my bike was purchased by a friend of mine, 4 years ago and once we had stripped away the lovely paint job is was a dog. issues ive already stated, but more seriously the chain split link had been ground away to fit the chain, seriously there was less than 1mm of metal eith...
by grumpus
Sun Dec 30, 2018 12:13 pm
Forum: Engine, Clutch & Gearbox
Topic: Engine mounts
Replies: 11
Views: 1665

Re: Engine mounts

Hi guys,
thanks for the info.
I'm in Cornwall so not able to collect. postage to me an option?
Plus an image of the assembly would be great if you could do that.
Many thanks.
by grumpus
Sat Dec 29, 2018 5:48 pm
Forum: Engine, Clutch & Gearbox
Topic: Engine mounts
Replies: 11
Views: 1665

Engine mounts

Bit of a long shot ,but here goes! So Im ready to re-fit my engine but both the spacer tubes that fit between the rubber mounts at the bottom of the engine are missing. They were missing when the bike was stripped, so I've not misplaced them! I've asked Ian but so far he has drawn a blank. My buddy ...